↓ Skip to main content

Elecrow ThinkNode M3 Review: A Pocket MeshCore Radio (Unboxing, Flashing, Setup)

·1662 words·8 mins
Lazy Product Reviews
Author
Lazy Product Reviews
I like to open boxes

Affiliate links: I may earn a small commission if you purchase through these links, at no extra cost to you.

Description
#

The Elecrow ThinkNode M3 is a small, screenless LoRa mesh node with GPS, a temperature and humidity sensor, a buzzer and IP66 weather resistance. In this video I unbox it, flash MeshCore onto it, pair it with the MeshCore app and send the first messages through my repeater.

Elecrow sent me this unit for review. The video isn’t sponsored and all opinions are my own.

Some links below are affiliate links: if you buy through them I may earn a small commission, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.

ThinkNode M3 on Amazon US: https://link.amazon/B0giDOCUM ThinkNode M3 on Elecrow’s site: https://www.elecrow.com/thinknode-m3-meshtastic-tracker-with-gps-wifi-ble-function-for-positioning.html

What I found:

  • Compact enough to pocket or clip to a bag
  • IP66: dust proof and fine with spray, not for submerging
  • Charges and flashes through a magnetic cable, not USB-C (replacement cables are on Elecrow’s website)
  • No screen, so pairing uses a fixed PIN
  • MeshCore firmware 1.15 and 1.17.1 worked for me; 1.16 did not
  • On the latest firmware, GPS and the sensor telemetry show up in MeshCore

Flashing steps shown in the video, using the MeshCore web flasher: https://flasher.meshcore.io (Chrome or Edge on a computer)

  1. Connect the M3 with the magnetic cable
  2. Put it in DFU mode
  3. First install only: erase the flash (skip this on an upgrade, it wipes your data)
  4. Put it back in DFU mode and flash the Companion Bluetooth firmware
  5. Pair in the MeshCore app and set your radio region

Chapters 0:00 Intro and disclosure 0:27 Unboxing 1:02 Features and what’s in the box 1:44 IP66 and where I’d use it 2:28 The magnetic charging cable 2:57 Flashing MeshCore 4:19 Pairing with the MeshCore app 4:58 Radio setup and first messages 5:56 GPS and telemetry 6:57 Final thoughts

#MeshCore #LoRa #ThinkNodeM3 #Elecrow #Meshtastic

Original Video: https://www.youtube.com/watch?v=uYEvnzkaerY

Transcript
#

Hey all, today we’ll be looking at this. This is a ThinkNode M3. This was sent to me by Elecrow for review. Now this isn’t sponsored by them, but they did provide it for me for review. So just full transparency right there. But everything I say will be my own opinions about this device. I have been a big fan of Meshtastic and MeshCore as a hobby. It’s quite fun. So I’m looking forward to taking a look at this. So I don’t know very much about this. So let’s open it up.

I’m keen to see what’s inside the box. And we have our manual right here. It’s a quick start guide, some protective film. This seems to be the device itself. That might be some sort of adhesive. We have a magnetic charger. How does this charge? Oh, it goes in. Oh, interesting. All right. That seems to be for mounting it, I guess, on a wall. And this seems to be a clip. So you could just have it dangling off a bag. Okay, cool. So there is a base, a buzzer, a button, a temperature and humidity sensor, indicator light, lanyard hole, adhesive tape if we wanted to like stick it to something, magnetic charging port underneath.

So yeah, there’s no screen on this unit. And so I guess you would charge it like that. And I guess that’s how we’ll flash it as well. That is USB. Is there a USB-C adapter? There is not. So I’m going to have to adapt that so we can flash it. We won’t be looking at these because I’m not going to be drilling any holes. That is kind of neat. That just kind of is its own little self-contained unit. Does it say anything about waterproofing? IP66. Okay, so this has IP66, which makes it dustproof.

And it can get a little bit wet, but you cannot submerge this in water. If it got sprayed with water, it won’t break. So it’s semi-rugged. And I guess this is something you could like put this outside. And then when you need to recharge it, you just clip it back in. Although if I had something that was outside permanently, I personally would want something that’s always on. Not sure I’ll be using this again either. I do like it for its portability. This could be really fun for having something you can just throw in your bag and just run MeshCore on, which would be pretty fun.

Having a proprietary plug for charging. I don’t know if this is at all standard. Maybe it is. Maybe you can get similar ones like this, but yeah, that’s frustrating. It does look like it will be fun, but there are some gotchas, like having this specific cable for charging. Maybe we can look it up and see if we can get another charging cable or see if this can get a USB-C version. I’m going to take a look at this thing and get to work on it. Okay, so now we’re going to start the flashing process.

Now, it’s actually been several weeks. I’ve had this for a while. I’ve already tested it. So what we’re going to do is on the MeshCore flasher at meshcore.io, right? We find our node. This is the ThinkNode M3. Just make sure you’re connected with the magnetic adapter into USB or a USB to USB-C adapter if you need one of those. And we’re going to flash the companion Bluetooth firmware. Now, you can use this firmware here. This does work fine. During most of the testing I had done, it was under firmware 1.15 and 1.17.1 also worked.

1.16 did not work at all for me. Before you begin the process, you first need to put the device in DFU mode. So you pick this right here. That puts it into DFU mode, right? DFU mode activated. And now when you first get the device, I highly recommend you erase the flash. Now, if you’re doing an upgrade, do not erase the flash because that will also erase your user data. So if you don’t have that backed up, you will lose it. All right, so the flash is erased.

Now to install MeshCore, you need to put it back into DFU mode. All right, DFU mode is active. And we can flash it just like that. Hit connect. And now it is installing MeshCore onto device. Okay, so it made a sound. Now that means it worked. So we need to use a MeshCore client. Now this doesn’t have a screen. So it has a fixed code, which I believe is 123456. The same thing I use on my luggage. So you will need the MeshCore app. I have it on my phone.

So if we go onto my phone here, we can see at the top, there is my MeshCore device. Okay, so now we need to pair it. So we can click here. And we’ll need to enter our pin. And since this is the first time we’re using it, we’ll do 123456 pair. And now we can continue to set it up. So we’ll continue testing, right, just like that radio country. I’m in Australia. So we’ll do Australia mid. That’s what we use where I am. And we’re done.

And we can quickly add a channel, create a join a hashtag channel and we’ll connect to test join channel. Okay, continue to channel. And we’ll type test and we’ve got one repeat. So it is working. It’s been picked up by my repeater. So it is all working just fine. I don’t seem to be able to hear anyone else right now for whatever reason. The MeshCore network in my area changes a lot. And I might not have any peers up there we go. And I’ve received some pings from the network.

So it is working just fine. It reached out to my repeater, everything is working as you would expect. That is the ThinkNode M3. Now when I was using this with MeshCore, I did not have access to the GPS, I don’t believe. I don’t think I had access in the newer firmware either. Okay, it does seem the MeshCore GPS does work on this device. So we have position. Let’s see what telemetry data we have. That’s also very good. This wasn’t working before either on the older firmware.

It seems the temperature sensor is working along with the battery. Now I am indoors. So that could explain why the GPS hasn’t gotten a location. But it is showing up in the telemetry. So I guess I can take this outside and confirm whether the position works at a later date. But that’s good to know the newer firmware fixed that and that was a problem before. And I’m glad I waited so long to get the video done because I wouldn’t be able to test it. So that’s cool.

That means I don’t need to install Meshtastic on this because I was going to show that Meshtastic, but it’s working now where it wasn’t working before. So that’s awesome. My final thoughts. Overall, I’m pretty happy with this after upgrading it to the latest firmware. It’s proven very useful. All the features are working GPS. All the sensors work. Yeah, it’s great. It’s compact, small, not a huge fan of this charger, just because it’s non-standard, but you can find replacements fairly easily. They’re on the Elecrow website. So that’s great.

And again, like you can just pocket this and just carry it with you. Yeah, there’s no screen, but who’s really using the screen on these MeshCore devices anyway. So it’s a great little gadget. Very happy Elecrow could send me this. And yeah, thanks again for watching and I hope to see you next time. And if you’re interested in picking one up for yourself, there’ll be a link in the description. See you. Bye.